![]() |
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 | ||
Regular Member
![]() Join Date: Nov 2008
Location: Sydney
Posts: 908
|
I posted this in the Tech section a couple of weeks ago - without response:
Can anyone tell me how to go about removing the Heater Fan control Knob on a AUIII XR8. The knob I have to replace it with has a lip on the end that will seem to lock into place when installed. My problem is removing the old one to replace it with the new one. Do I need to remove the trim panels around the radio/ Heater controls to do this?
__________________
MY18 Mustang GT MY18 Everest Trend Harley Davidson FXBRS |
||
![]() |
![]() ![]() |
![]() |
#2 | |||
not here much anymore
Join Date: Dec 2004
Location: Sthn NSW
Posts: 22,918
|
Quote:
headunit out find all philips head screws in dash and undo then pull the fascia off the heater controls then screw into that from the back so you can undo those screws, and then access the knobs.
__________________
2024 F150 XLT
|
|||
![]() |
![]() ![]() |
![]() |
#3 | |||
Regular Member
![]() Join Date: Nov 2008
Location: Sydney
Posts: 908
|
Quote:
I guess Ill set aside a couple of hours to do it ![]()
__________________
MY18 Mustang GT MY18 Everest Trend Harley Davidson FXBRS |
|||
![]() |
![]() ![]() |
![]() |
#4 | ||
With da Warlords
Join Date: May 2006
Location: Orange NSW
Posts: 1,781
|
^^^ As he said. Just be careful when pulling the fascia off, that you don't break any of the clips (or bloody cut yourself on the sharp edge like i do lol)
__________________
You don't have to be faster than the bear, you just have to be faster than the slowest guy running from the bear. For Sale: Parachute. Only used once, never opened, small stain. Windsor Warlords AU III XR-8220 ![]() ![]() XR50T Ute - 300rwkw (give or take depending on the day)
![]() |
||
![]() |
![]() ![]() |
![]() |
#5 | |||
not here much anymore
Join Date: Dec 2004
Location: Sthn NSW
Posts: 22,918
|
Quote:
It is fairly straight forward after that, I cant remember the location of all of the screws once you get the HU out but just have a good look around and you will find them. After that you should be able to firmly pull off the outer surround and access the AC controls, you will likely need to unplug all the looms etc to be able to take it out and work on it. Dont worry about that bit though because all of the plugs are different, so you cant plug them into the wrong spot (different sizes etc).
__________________
2024 F150 XLT
|
|||
![]() |
![]() ![]() |
![]() |
#6 | |||
not here much anymore
Join Date: Dec 2004
Location: Sthn NSW
Posts: 22,918
|
Quote:
![]()
__________________
2024 F150 XLT
|
|||
![]() |
![]() ![]() |